Showing Details of LED Street Light Installation Guide and Maintenance Procedure. If You Want to Prolong Street Lamp's Service Life, It Should be Regularly Maintained and Kept in Good Repair.

Haining, Zhejiang -- (SBWIRE) -- 10/19/2017 -- Although LED Street Lamp has a long lifespan, it is consumable. If you want to prolong its service life, it should be regularly maintained and kept in good repair. Below are some LED street light installation guides and maintenance procedures for your guidance.

- LED Street Lights Installation Tools

Installation kit includes complete sets of wrenches, 30cm live wrench, screwdriver, stripping pliers, multimeter, several conductors, 50m tape measure, electrician tape, working trucks with life table, warning signs, flash lamps with lift stations. Some of these tools will be provided by led street lighting suppliers.

- LED Street Lighting Install Cautions

To begin with, the construction personnel must have the related specialized knowledge. Then, to protect with a soft cloth or other protective material when road lamp is facing down. Furthermore, you must never operate in an electric environment. Finally, determine whether the weather is in line with outdoor high-power working range. You can't perform lamp pole installation work when the wind is over 4 class.

About how to install lamp-post, please click: Street Light Pole Installation Procedure.

- LED Street Light Installation Working Guide

Preparatory Work: Open the outer packing, remove the packing material above the lamp, and take out the LED road lamp. Then check whether the parts or accessories and the manual are complete according to the list of goods and accessories in the packing box. At last, check if the fasteners are solid, whether the lamp assembly is correct, make a Power debugging on street lights to confirm the lamp is working normally.

- Street Light Installation Guides

1, Connect the street lamp power wire onto the cable of the Lamp lever control box (or connector) while connecting a yellow or yellow-green wire to the ground line.

2, Then connect the black and white (or brown and blue) wires, make sure wire connection point must be fitted with the protective cover or waterproof treatment.

3, Lock the grounding wire to the screw of the driver if there is no yellow or yellow-green wire, and ensure the screws connect with the lamp metal casing.

4, Combination of the lamp cap hole and the cantilever. Adjust the direction of street lamps, so that the lights and the led street light module can be fully illuminated to the effective area of the road.

5, Tighten the screws and fix the LED Street Lamp and test if the light works normally.

- Electrical Safety measures

1, Distribution Box switch set separately and must insist on one-machine one-brake power with two-level leakage protection device. Power Distribution box, switch box must be installed firmly and pay attention to moisture.

2, On-site lighting: The lighting wire is well insulated and the guideline shall not be dragged or tied to the angle of the enclosure.

3, Distribution box and switch box: Use standard distribution box, the switchgear in the distribution box must be intact and undamaged and set leakage protector in the box. Metal Case Electric box must be made ground protection.

- Installation process example with HEPETECH modular led street light type T19A.

Please look for more details from LED Street Light Installation Guide and Maintenance Procedure.

For more information on this press release visit: http://www.releasewire.com/press-releases/release-3.htm

Haining, Zhejiang -- (SBWIRE) -- 10/09/2017 -- A lot of unqualified LED Globe Light Bulbs had been put into the LED lighting market by led light bulb manufacturers because of the vicious competition. Globe LED light bulbs are losing the real value of energy saving, long lifespan, and environmental protection. How to distinguish LED light bulbs? Maybe the following 8 tips will help you.

1. In the light of hardware's quality. The quality of the hardware is based on the quality of LED chips and drivers, and the packaging technology.

2. In the light of heat-removal system- material and frame. It's very important to lose heat for large globe light bulbs if the radiation condition is not good, the whole lamp body will work in a high temperature and will surely reduce its working lifetime. What's more, the Lumen depreciation and light failure will be very large.

3. In the light of Power Factor. The lower power factor, the worse LED driver, and circuit design. Low factor power makes LED products shorter lifetime, even they have the best cooling system.

4. In the light of LED Drive. The working time of LED globe light bulb determined by the LED driver. Because the driver's lifetime is much shorter than other parts. For example, the LED chips have 30,000 to 50,000 hours lifetime, but the driver only has 15,000 to 30,000 hours. LED driver's working time is based on the project design of power supply and material chosen.

5. In the light of lighting Light Effect. At the same power, the higher lighting effect, the brighter LED light bulbs. Therefore, At the same brightness, the power is much lower to saving the energy.

6. In the light of Power Efficiency. It's great for the LED bulb to have a higher power efficiency. Because if LED driver consumes less power, the light source will output more power.

7. In the light of Quality. Good quality large round globe light bulbs should meet other requirements just like dustproof and waterproof protection, antimagnetic, surge protection, leakage protection and so on.

Hope these 7 tips will do you a favor on choosing LED globe bulbs. More details, please look at http://www.broled.com.

For more information on this press release visit: http://www.releasewire.com/press-releases/release-3.htm

How to choose suitable LED Street Lamps for different applications? You can make the streetlight choices according to the lighting requirements of interchange, plaza, and other using areas, or to the application of dustproof and waterproof requirements.

Haining, Zhejiang -- (SBWIRE) -- 10/03/2017 -- Because of working outdoors for a long time and the bad working environment, Roadway LED Street Lamp must meet the higher requirements in the aspect of optical properties, mechanical strength, dustproof waterproof level, corrosion resistance, heat resistance, electrical insulation properties.

Then how to choose a suitable LED Street Light for different applications?

Firstly, select the appropriate led road lamp according to the lighting requirements of interchange, plaza, and other using areas.

- Roads of the yard and residential district, pedestrian street of the commercial district, the square and other places, they will be installed on higher mechanical strength street lights.

- We can select cut-off or half cut-off lamps for collector streets as a general rule.

- Basically, we choose the Flood LED Lamp for high mast lighting.

Secondly, choosing the Roadway LED streetlight according to the application of dustproof and waterproof requirements.

We use two numbers followed by characteristic letters "IP" to express the classes of waterproof and dustproof protection. The first letter "I" has the following meanings:

- 0, Unprotected. I.E., no any special protection.
- 1, The lamp can defend solid foreign bodies of greater than 50 mm.
- 2, The lamp can defend solid foreign bodies of greater than 12 mm.
- 3, The lamp can defend solid foreign bodies of greater than 2.5 mm.
- 4, The lamp can defend solid foreign bodies of greater than 1mm.
- 5, Dust prevention.
- 6, Excellent air-tightness and dustproof. That is, without any dust entering.

The meanings of the second letter "P" are as follows:

- 0, Unprotected.
- 1, Drop-proof.
- 2, Drop-proof under the angle of inclination 15 degrees.
- 3, Protected against spraying.
- 4, Splashproof.
- 5, Protected against water jets.
- 6, Heavy-sea-proof.
- 7, Flooding safety.
- 8, Protected against submersion.

We can choose the proper protection grade products according to the environmental conditions. In general, IP65 is the basis protection for outdoor roadway LED Street Lamp, and IP68 is the highest degree of protection, most of the LED light modules of modular led street lights from Hepetech are IP68.

The above content is adapted from www.hepetech.com.

For more information on this press release visit: http://www.releasewire.com/press-releases/release-3.htm